Shaft-mount helical reducer · ratios 5:1–25:1 · 3–60 hp. New price, used price, and a real standard-shop-vs-in-house repair comparison — actual cost and lead time — plus specs. Or sell your surplus Torque-Arm II TA for cash.
Have this unit? Snap the nameplate for an instant quote →
| New / retail (OEM)list price, new unit | $1,500–$6,800 |
| Used (working)secondhand, tested | $850–$5,100 |
Researched estimates anchored to OEM pricing; a new Torque-Arm II TA commonly runs a 16–30 week lead time for comparison. Send your nameplate for a confirmed number.
We’ve bought, sold, and rebuilt industrial gearboxes for years — we know the Dodge Torque-Arm line, not just gears in general. That experience shows up in a correct diagnosis the first time.
Standard rebuilds ship in 5–14 business days with 24–72-hour emergency service — while a new unit can be 16–30 weeks out. We get your line running sooner.
You see the full picture before you commit — retail, used, surplus, repair, and a cash offer. Some shops take your unit in, tear it down, and only then hand you a quote you’re effectively forced to accept. We give you the numbers first.
Your gearbox is never held hostage. If repair isn’t the smart move, we’ll tell you — and we’ll buy the unit for cash so you walk away ahead instead of paying to get a paperweight back.
The Dodge Torque-Arm II TA is a shaft-mount helical reducer from Dodge’s Torque-Arm line, rated 3–60 hp across ratios of 5:1–25:1, and commonly found on bulk conveyors, aggregate, mining. Because Dodge is the Tigear and Torque-Arm workhorses found on virtually every bulk-material conveyor in the country, these units turn up constantly for both rebuild and surplus buyback. When one fails the real question is never just "what does a repair cost" — it’s how our in-house repair cost and lead time compare to a standard shop, and how fast you can be running again. That side-by-side is exactly what the comparison above gives you, and it’s information most repair sites simply don’t publish.
On the Torque-Arm II TA, typical failure modes are bearing wear, shaft-seal leakage, and gear-tooth pitting from degraded or contaminated oil. Most units are fully rebuildable. A correct rebuild means full teardown, hot-tank cleaning, magnetic-particle inspection of all gearing for hidden cracks, verification of bearing-bore tolerances, new bearings, seals, shims and gaskets, reassembly to factory clearances, and a loaded run-test. Done right, that restores a fresh service life at a fraction of replacement — and our in-house cost and lead time come in below a standard shop, with the exact dollars and days shown in the comparison above, versus the 16–30 weeks a new Torque-Arm II TA can take to arrive.
Here’s the part worth being honest about: repair isn’t always the answer. If the housing is cracked or the gears are unavailable, a used, surplus, or reman Torque-Arm II TA may be cheaper and faster than rebuilding — and if that’s the case we’ll say so and buy your failed unit for cash rather than talk you into a repair that doesn’t pay. That two-way position is deliberate. A shop that only earns money when you repair has every reason to take your gearbox in, disassemble it, and hand you a quote you can no longer walk away from. We put every number in front of you first, and we don’t hold your equipment while we do it.
The Torque-Arm II TA should be rebuilt by an AGMA-experienced industrial gear shop with in-house gear cutting (hobbing and grinding) and NDT capability — not a general machine shop — and that is exactly the caliber of partner we route these jobs to. Combined with years in the industrial equipment business, that’s why the Dodge units we handle come back right the first time. And if you have surplus Torque-Arm II TA units on the shelf, they carry real value — send the nameplate and we’ll turn them into cash.
| Brand / line | Dodge — Torque-Arm |
| Model / part number | Torque-Arm II TA |
| Type | Shaft-mount helical reducer |
| Nominal ratios | 5:1–25:1 |
| Power range | 3–60 hp |
| Size / frame | TA sizes 07–115 |
| Typical applications | bulk conveyors, aggregate, mining |
| OEM lineage | Dodge / RBC Bearings |
Confirm exact ratio and rating from your nameplate — we service and buy all configurations of the Torque-Arm II TA.
Full disassembly, hot-tank strip, oil passages cleared.
All gearing NDT-checked for hidden cracks; bores measured.
All-new bearings, seals, shims, gaskets; seal surfaces reground.
Set to factory clearances, painted, loaded run-test, warranty.